How do I identify an Alko hub?

AL-KO axles are identified by the oval plate fitted on the rear of each axle.

How do you grease caravan wheel bearings?

YouTube video

How do you change a bearing on a caravan?

YouTube video

How do I identify an Alko hub? – Related Questions

How often should you change wheel bearings on a caravan?

It is recommended that you inspect and repack your trailer or caravan wheel bearings at least once a year and replace if worn or damaged. It is also a good idea to carry at least one spare caravan wheel bearing kit and grease, especially if travelling in remote areas.

How often should you do wheel bearings on a caravan?

A Wheel Bearing and Brake service is one of the most essential, maintenance requirements for any Trailer or Caravan. The wheel bearings should be checked and regreased every 12 months or 10,000km, whichever occurs first.

How do you check caravan bearings?

YouTube video

How can you tell which wheel bearing is bad?

The symptoms of bad wheel bearings include:
  1. Noise: A humming, rumbling or growling noise that increases with acceleration or as the vehicle turns.
  2. Looseness, excessive play in the steering wheel (vague steering);
  3. Steering wheel vibration which changes with the vehicle speed or as the vehicle turns;
  4. ABS malfunctioning.

How do you remove a rear wheel bearing without a puller?

Steps to take if you want to know how to remove bearing from the shaft without a puller
  1. Select the right surface.
  2. Apply the vehicle’s parking brake.
  3. Use a car jack to raise your vehicle.
  4. Place jack stands under your vehicle.
  5. Remove the coverings and trays that are in the way.
  6. Remove the tires.

What temperature should Caravan wheel bearings run at?

A simple rule for troubleshooting bearing temperatures: No more than 180 degrees Fahrenheit (82 degrees Celsius) on the housing. The bearing outer ring can be up to 20°F (11°C) hotter than the housing.

Can you over tighten wheel bearings?

Over-tightening can damage the lug nuts, wheels and hubs – and worse, result in a wheel-off situation.

How hot is too hot for a bearing?

Bearing Temperature Conditions

A bearing temperature that is less than 180 degrees F is typically considered acceptable (see the chart below). Of course, there may be other consequences for operating in this “good” range. A higher operating temperature will cause the bearing lubricant to deteriorate at a faster rate.

How hot is too hot for trailer hubs?

If you were getting over 200 degrees that would be a bad sign. But typically if all of the hubs are the same temperature you’re good and it’s only really an issue if one of the hubs is hotter than others.

Can you put too much grease in a wheel bearing?

Too much grease causes churning and higher temperatures. Semi-fluid grease must be used with a vented hub cap. It cannot be packed around the bearing as it will slump.

How tight should an axle nut be on a trailer?

Correct Torque Rating for a Trailer Wheel Spindle Nut The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.

How do I know if I need new wheel bearings on my trailer?

Check wheels for side-to-side looseness – There should be a very slight amount of play in the wheel, typically 1/8-inch or less. If the wheels are loose or spin with a wobble, the bearings must be serviced or replaced.

How often should I grease my trailer bearings?

With a larger travel trailer, you should grease your trailer wheel bearings every 10,000 miles or once a year, whichever comes first. If you have a smaller travel trailer, however, you’ll need to grease your wheel bearings every 2,000 miles. This is because the wheels are smaller and spin faster.

How often should trailer bearings be replaced?

The axle manufacturers recommend that you repack your trailer bearings once annually or every 12,000 km.

Leave a Comment